Seedling propagating bed – two week update

19 Apr

First – there are seedlings growing!

S seedling bed improvements 002

And quite a lot of them. The first seedlings came up after about 7 days, and now there is at least one seedling growing in 215 of the 350 pots.

An automatic cutoff when the bed is flooded.

S seedling bed improvements 004

This is a simple float switch. When the float (a section of pool noodle) is lifted by the water, the wire rotates around a bearing and presses the microswitch which cuts off power to the pump. There’s a “control panel” visible to the left. Pressing the square button powers up a relay which turns on the pump, but it also supplies power to the relay so it keeps running after you take your finger off the button. When float rises, it cuts power to the relay which switches off, and stays off until pressing the button starts the cycle again. There’s also an override switch, a fuse, and an LED to light up.

FISH!

S seedling bed improvements 008

As the water flowed across the bed, then sat in the reservoir, it started forming algae. We started considering options to stop the buildup, then hit on the idea of advancing towards our eventual goal of aquaponics by adding a couple of fish to the system. We’ve always intended to have goldfish as part of the larger system we’re planning, but we had to do some furious research to see if it was workable.

The reservoir is renamed “the fish tank”

S seedling bed improvements 010

A visit to a pet shop netted us two quite small fish, some fish-food, a thermometer, and an air pump. I modified an old sieve by cutting holes for outlet pipes and wires, then placed two water pumps (the original pump and a smaller one) inside the sieve. A collection of stones from the beach at Birdlings Flat and a couple of chunks of brick all serve to hold the sieve firmly against the bottom of the tank. I’m fairly confident that the fish won’t be able to get near the pump intakes. The air pump is outside the tank, with a hose leading to the bottom of the tank. We used it before the fish moved in to make sure the water was well oxygenated but haven’t kept it up as (a) it was really too loud and vigorous, and (b) it ran off 240V whereas everything else is running off 12V (solar) power. As an alternative, the second (small) water pump inside the sieve feeds out to a hose which splashes water back into the tank, adding oxygen in the process.

The algae has gone, the fish seem happy, and they have definitely grown.

Anti-cat barrier and air circulation fans.

S seedling bed improvements 001

We strung some loose strands of bright 4mm rope on three sides to dissuade the cats from jumping up onto the seedlings. Seems to have worked so far.

We’re quite worried about “damping off”, the fungal disease(s) that like to destroy young seedlings. The seedling pots are quite moist and, while we haven’t had any problems so far, conditions are quite good for fungus to develop. Many sources recommend fans moving the air about to dry the top layer of soil, prevent stagnant moist air from sitting around, and also toughen up the young seedlings. I didn’t want to use a mains powered fan so I grabbed eight PC fans salvaged from various computers and hooked them up. They’re hooked up in pairs, with each pair joined in series so the fans, designed for 12V, only get half the voltage (6V) and turn over slowly and quietly. It took a surprising amount of time to hook them up but they seem to work very well. The biggest problem, and one that almost caught me out, is that each pair of fans should be of similar power. I was amazed how many different ratings there were in the my fan collection – each of the four pairs in use here is a quite different rating.

More controls

S seedling bed improvements 005

Each step we take seems to require more controls, especially adding the fish. I really need to add some timers to the system, and perhaps a water level detector for the fish tank. Perhaps a moisture detector to tell how damp the soil is. Lots of options. I’ve started working up a system based on an Arduino microcontroller.

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: